Category:234 Interchanges: Difference between revisions
No edit summary |
No edit summary |
||
Line 31: | Line 31: | ||
Cloverleaf interchanges can be used where two high volume freeways intersect. Loop-ramps are used to accommodate left-turning movements. However, this configuration provides short weaving areas for traffic entering or leaving the interchange. A cloverleaf interchange occupies a relatively large area of right of way. | Cloverleaf interchanges can be used where two high volume freeways intersect. Loop-ramps are used to accommodate left-turning movements. However, this configuration provides short weaving areas for traffic entering or leaving the interchange. A cloverleaf interchange occupies a relatively large area of right of way. | ||
[[Image:234.2 DDI.jpg|thumb|left|<center>Diverging Diamond Interchange (DDI)</center>]] | |||
In some circumstances, a “basic” interchange may not be the appropriate choice to satisfy the needs of the traveling public. The interchange that is designed may be a combination of the basic types or incorporate [[Media:234.2 Creative Diamnond Interchange Arrangements.pdf|creative modifications]]. A Diverging Diamond Interchange (DDI) is one example. | In some circumstances, a “basic” interchange may not be the appropriate choice to satisfy the needs of the traveling public. The interchange that is designed may be a combination of the basic types or incorporate [[Media:234.2 Creative Diamnond Interchange Arrangements.pdf|creative modifications]]. A Diverging Diamond Interchange (DDI) is one example. | ||
The high cost of construction restricts the use of an interchange to those situations where the expenditure is justified. An interchange “warrants” construction based on consideration of the roadway’s design designation, traffic volume and safety of operation. | The high cost of construction restricts the use of an interchange to those situations where the expenditure is justified. An interchange “warrants” construction based on consideration of the roadway’s design designation, traffic volume and safety of operation. |
Revision as of 14:50, 19 December 2006
The selection of an appropriate interchange is influenced by such factors as highway classification, composition of traffic, anticipated operating speed, economics, terrain, available right of way and the degree of access control. An interchange is to be considered when warranted by the 20-year design traffic projection or safety concerns. An interchange will provide access for all traffic movements. The desired spacing between interchanges is two miles in current and projected urban areas and five miles in rural areas. Access Management Guidelines are also considered to determine the spacing of interchanges.
At times it may be necessary to construct a new interchange or revise an existing interchange on an interstate highway. When this occurs, justification must be provided to FHWA for approval before the work can begin.
Basic types of interchanges are:
Chapter 10 of the AASHTO Green Book provides examples of these interchange types. Controlling factors in the selection of an interchange type are: right of way requirements, vehicle speed, traffic volume, terrain, access control and cost. Interchanges are designed to fit specific local conditions and meet driver expectations.
Diamond interchanges are suitable in both rural and urban areas when the traffic on the minor crossroad is light to moderate. The greatest impediment to smooth operation is the volume of left-turning movements on the crossroad. Signal operations must be considered when designing a diamond interchange. Spacing between the ramps is critical for efficient movement of traffic through the interchange.
Directional interchanges accommodate high volume turning movements where two freeways intersect. Direct ramp movements reduce travel distance, increase speed and capacity, eliminate weaving and avoid the need for “out-of-direction” travel on a loop. These interchanges are costly to construct due to the increased number and length of ramps and the number of bridge crossings.
Single-point urban interchanges (SPUI) were first constructed in the early 1970’s. Their primary feature is all four turning movements intersect at a common point. Therefore, the number of signals needed to control traffic is reduced. Furthermore, opposing left turn movements pass to the left of each other
Cloverleaf interchanges can be used where two high volume freeways intersect. Loop-ramps are used to accommodate left-turning movements. However, this configuration provides short weaving areas for traffic entering or leaving the interchange. A cloverleaf interchange occupies a relatively large area of right of way.
In some circumstances, a “basic” interchange may not be the appropriate choice to satisfy the needs of the traveling public. The interchange that is designed may be a combination of the basic types or incorporate creative modifications. A Diverging Diamond Interchange (DDI) is one example.
The high cost of construction restricts the use of an interchange to those situations where the expenditure is justified. An interchange “warrants” construction based on consideration of the roadway’s design designation, traffic volume and safety of operation.
Articles in "234 Interchanges"
The following 6 pages are in this category, out of 6 total.