903.23 Laboratory Testing Guidelines for Sec 903: Difference between revisions
m →903.24.1.4 Aluminum Welding: Per BR and CM, E 903.24.1.4.1 and E 903.24.1.4.2 were deleted to removed archaic welder qualification info. |
m Per TS, minor updates |
||
| (One intermediate revision by the same user not shown) | |||
| Line 2: | Line 2: | ||
This article establishes procedures for Laboratory testing and reporting samples of material used for installation of highway signing including nuts, bolts, washers, polyurethane foam and specimens for welder qualifications. | This article establishes procedures for Laboratory testing and reporting samples of material used for installation of highway signing including nuts, bolts, washers, polyurethane foam and specimens for welder qualifications. | ||
==903. | ==903.23.1 Procedure== | ||
===903. | ===903.23.1.1 Bolts, Nuts and Washers=== | ||
Chemical tests, consisting of mass of coating, shall be determined according to AASHTO M232. Chemical analysis of the base metal shall be determined, when requested, according to [[:Category:1020 Corrugated Metallic-Coated Steel Culvert Pipe, Pipe-Arches and End Sections#1020.8.1.1 Chemical Tests|EPG 1020.8.1.1 Chemical Tests]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through | Chemical tests, consisting of mass of coating, shall be determined according to AASHTO M232. Chemical analysis of the base metal shall be determined, when requested, according to [[:Category:1020 Corrugated Metallic-Coated Steel Culvert Pipe, Pipe-Arches and End Sections#1020.8.1.1 Chemical Tests|EPG 1020.8.1.1 Chemical Tests]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWare. | ||
Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Original test results and calculations shall be recorded through | Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Original test results and calculations shall be recorded through AASHTOWare. | ||
===903. | ===903.23.1.2 Polyurethane Foam=== | ||
Tests on samples of polyurethane foam shall be conducted in accordance with the following methods: | Tests on samples of polyurethane foam shall be conducted in accordance with the following methods: | ||
| Line 17: | Line 17: | ||
:(b) Density - ASTM D1622 | :(b) Density - ASTM D1622 | ||
Original test results and calculations shall be recorded through | Original test results and calculations shall be recorded through AASHTOWare. | ||
===903. | ===903.23.1.3 Structural Steel Welding=== | ||
Samples of structural steel welding shall be tested in accordance with [[:Category:712 Structural Steel Construction#712.3.2.3 Structural Steel Welding|EPG 712.3.2.3 Structural Steel Welding]]. | Samples of structural steel welding shall be tested in accordance with [[:Category:712 Structural Steel Construction#712.3.2.3 Structural Steel Welding|EPG 712.3.2.3 Structural Steel Welding]]. | ||
===903. | ===903.23.1.4 Aluminum Welding=== | ||
Tests shall be performed in accordance with Section IX of the ASME Boiler and Pressure Vessel Code. | Tests shall be performed in accordance with Section IX of the ASME Boiler and Pressure Vessel Code. | ||
==903. | ==903.23.2 Sample Record== | ||
Test results for bolts, nuts, washers, and polyurethane foam shall be documented on the appropriate templates in | Test results for bolts, nuts, washers, and polyurethane foam shall be documented on the appropriate templates in AASHTOWare. The sample record is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. | ||
Procedure qualification test results for welds shall be reported through | Procedure qualification test results for welds shall be reported through AASHTOWare. Welder qualification test results are also reported through AASHTOWare. | ||
Current welder qualification status is maintained in | Current welder qualification status is maintained in AASHTOWare by Bridge Engineering. | ||
[[Category:903 Highway Signing]] | [[Category:903 Highway Signing]] | ||
Latest revision as of 09:56, 27 April 2021
This article establishes procedures for Laboratory testing and reporting samples of material used for installation of highway signing including nuts, bolts, washers, polyurethane foam and specimens for welder qualifications.
903.23.1 Procedure
903.23.1.1 Bolts, Nuts and Washers
Chemical tests, consisting of mass of coating, shall be determined according to AASHTO M232. Chemical analysis of the base metal shall be determined, when requested, according to EPG 1020.8.1.1 Chemical Tests. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWare.
Physical tests shall be conducted according to EPG 712.3.2.2 Physical Tests - Bolts and Nuts. Original test results and calculations shall be recorded through AASHTOWare.
903.23.1.2 Polyurethane Foam
Tests on samples of polyurethane foam shall be conducted in accordance with the following methods:
- (a) Compressive Strength - ASTM D1621
- (b) Density - ASTM D1622
Original test results and calculations shall be recorded through AASHTOWare.
903.23.1.3 Structural Steel Welding
Samples of structural steel welding shall be tested in accordance with EPG 712.3.2.3 Structural Steel Welding.
903.23.1.4 Aluminum Welding
Tests shall be performed in accordance with Section IX of the ASME Boiler and Pressure Vessel Code.
903.23.2 Sample Record
Test results for bolts, nuts, washers, and polyurethane foam shall be documented on the appropriate templates in AASHTOWare. The sample record is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in EPG 106.20 Reporting, are to be included in the remarks to clarify conditions of acceptance or rejection.
Procedure qualification test results for welds shall be reported through AASHTOWare. Welder qualification test results are also reported through AASHTOWare.
Current welder qualification status is maintained in AASHTOWare by Bridge Engineering.