1039.4 Laboratory Testing Guidelines for Sec 1039: Difference between revisions
info from lab manual |
m Per BR, renamed EPG 1039 Epoxy Resin Material to EPG 1039 Polymer Products to coordinate with new Sec 1039 title |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
This article establishes procedures for Laboratory testing of epoxy resins. Refer to [http://www.modot. | This article establishes procedures for Laboratory testing of epoxy resins. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1039] for MODOT's specifications. | ||
==1039.4.1 Sample Preparation== | ==1039.4.1 Sample Preparation== | ||
| Line 24: | Line 24: | ||
===1039.4.2.2 Bonding Agents for Dowels=== | ===1039.4.2.2 Bonding Agents for Dowels=== | ||
Determine the properties of bonding agents for dowels according to [[106. | Determine the properties of bonding agents for dowels according to [[106.3.2.49 TM-49, Pull-Out Tests on Chemical Bonding Agents|MoDOT Test Method T49]]. | ||
Run an Infrared Spectrum on each component. | Run an Infrared Spectrum on each component. | ||
| Line 32: | Line 32: | ||
===1039.4.2.3 Bonding Agents for Resin Anchor Systems=== | ===1039.4.2.3 Bonding Agents for Resin Anchor Systems=== | ||
Determine the properties of bonding agents for resin anchor systems according to ASTM C 881. Perform the pull test in accordance with [[106. | Determine the properties of bonding agents for resin anchor systems according to ASTM C 881. Perform the pull test in accordance with [[106.3.2.74 TM-74, Pullout Tests on Epoxy Bonding Agents for Resin Anchor Systems|MoDOT Test Method T74]]. | ||
Run an Infrared Spectrum on each component. | Run an Infrared Spectrum on each component. | ||
| Line 40: | Line 40: | ||
===1039.4.2.4 Sand for Epoxy Mortar=== | ===1039.4.2.4 Sand for Epoxy Mortar=== | ||
Test sand for epoxy mortar for compliance with [http://www.modot. | Test sand for epoxy mortar for compliance with [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1039]. Determine the moisture content in a laboratory oven. | ||
Record original test data and calculations in Laboratory workbooks. | Record original test data and calculations in Laboratory workbooks. | ||
[[Category:1039 | [[Category:1039 Polymer Products]] | ||
Latest revision as of 12:08, 4 February 2020
This article establishes procedures for Laboratory testing of epoxy resins. Refer to Sec 1039 for MODOT's specifications.
1039.4.1 Sample Preparation
These materials are furnished as multiple-component systems. The mixing ratio of components must be the same as that used to obtain Manufacturer and Brand Name Approval.
1039.4.2 Procedure
1039.4.2.1 Type II and III Epoxy
Test components by obtaining an Infrared Spectrum.
Test the mixed material according to the following:
- Viscosity, Brookfield viscometer as set forth in ASTM D 2393.
- Gel Time, ASTM C 881
Test the mixed and cured material according to the following:
- Bond Strength, ASTM C 882
- Tensile Strength and Elongation at Break, ASTM D 638
1039.4.2.2 Bonding Agents for Dowels
Determine the properties of bonding agents for dowels according to MoDOT Test Method T49.
Run an Infrared Spectrum on each component.
Record original test data and calculations in Laboratory workbooks.
1039.4.2.3 Bonding Agents for Resin Anchor Systems
Determine the properties of bonding agents for resin anchor systems according to ASTM C 881. Perform the pull test in accordance with MoDOT Test Method T74.
Run an Infrared Spectrum on each component.
Record original test data and calculations in Laboratory workbooks.
1039.4.2.4 Sand for Epoxy Mortar
Test sand for epoxy mortar for compliance with Sec 1039. Determine the moisture content in a laboratory oven.
Record original test data and calculations in Laboratory workbooks.