Category:1058 Polyethylene Sheeting - Revision history

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-10-18T15:10:00Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 10:10, 18 October 2021
Line 10:		Line 10:
	===1058.1 Procedure===		===1058.1 Procedure===

	The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker between a bridge approach slab and a granular base. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through ~~SiteManager~~.		The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker between a bridge approach slab and a granular base. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through AASHTOWARE Project (AWP).

	A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1058] is below.		A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1058] is below.
Line 31:		Line 31:
	===1058.2 Report (Records)===		===1058.2 Report (Records)===

	When polyethylene sheeting is accepted in the field, it is to be reported through		When polyethylene sheeting is accepted in the field, it is to be reported through AWP and the manufacturer's certification, when used for acceptance, is to be retained in the district office. The report is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify the conditions of acceptance or rejection.
	~~SiteManager~~ and the manufacturer's certification, when used for acceptance, is to be retained in the district office. The report is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify the conditions of acceptance or rejection.

	Distribution of reports for materials purchased under a Department purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|EPG 1101 Materials Purchased by a Department Purchase Order]].		Distribution of reports for materials purchased under a Department purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|EPG 1101 Materials Purchased by a Department Purchase Order]].

Smithk: /* Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM) */

2019-04-24T14:16:31Z

Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM)

← Older revision		Revision as of 09:16, 24 April 2019
Line 20:		Line 20:
	! style="background:#BEBEBE" \|Brand Name!!style="background:#BEBEBE"\| Manufacturer		! style="background:#BEBEBE" \|Brand Name!!style="background:#BEBEBE"\| Manufacturer
	\|-		\|-
	\|HydrAdsorb \|\|~~FirstLine~~ Corp.		\|HydrAdsorb \|\|Fortifiber Corp.
	\|-		\|-
	\|rowspan="2" \|(02/05)\|\| 511 Highland Drive		\|rowspan="2" \|(02/05)\|\| 511 Highland Drive

Smithk: updated link

2018-10-11T20:06:57Z

updated link

← Older revision		Revision as of 15:06, 11 October 2018
Line 3:		Line 3:
	\|'''MGS Information'''		\|'''MGS Information'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov/business/materials/pdf~~/mgs~~/MGSINDEX.pdf~~ Current General Services Specifications (MGS) By Subject]		\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]
	\|}		\|}

Smithk: updated link

2016-06-15T18:34:56Z

updated link

← Older revision		Revision as of 13:34, 15 June 2016
Line 6:		Line 6:
	\|}		\|}

	This article establishes procedures for inspecting, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting polyethylene sheeting. Refer to [~~http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf~~ Sec 1058] for MoDOT’s specifications.		This article establishes procedures for inspecting, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting polyethylene sheeting. Refer to [ Sec 1058] for MoDOT’s specifications.

	===1058.1 Procedure===		===1058.1 Procedure===
Line 12:		Line 12:
	The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker between a bridge approach slab and a granular base. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through SiteManager.		The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker between a bridge approach slab and a granular base. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through SiteManager.

	A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1058~~.pdf Sec 1058] is below.		A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1058] is below.

	===<center>Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM)</center>===		===<center>Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM)</center>===

Smithk: /* 1058.1 Procedure */ Per Bridge, a clarification of where the bond breaker is to be used.

2011-10-27T19:45:59Z

1058.1 Procedure: Per Bridge, a clarification of where the bond breaker is to be used.

← Older revision		Revision as of 14:45, 27 October 2011
Line 10:		Line 10:
	===1058.1 Procedure===		===1058.1 Procedure===

	The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker ~~under~~ bridge approach ~~slabs~~. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through SiteManager.		The Resident Engineer may accept polyethylene sheeting, for use in curing Portland cement concrete or use as a bond breaker between a bridge approach slab and a granular base. However, if Construction and Materials is requested to perform inspection, the material may be accepted on the basis of manufacturer's certification or sampling and testing, if deemed necessary. When a shipment is sampled, the number of rolls to be sampled is one half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing through SiteManager.

	A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] is below.		A list of those manufacturers who have submitted for New Product Evaluation and provided certification that their product meets the requirements of [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] is below.

Smithk: updated links

2010-07-01T16:17:44Z

updated links

← Older revision		Revision as of 11:17, 1 July 2010
Line 6:		Line 6:
	\|}		\|}

	This article establishes procedures for inspecting, [[106.5 Sampling\|sampling]] and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.		This article establishes procedures for inspecting, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.

	===1058.1 Procedure===		===1058.1 Procedure===
Line 27:		Line 27:
	\|}		\|}

	This qualified list does not represent all products that may be used for those applications listed in Sec 1058. Other products may be accepted based on certification provided to the inspector at the jobsite or on sampling and testing. However, those companies that submit to Construction and Materials for [[106.19 New Product Evaluation\|New Product Evaluation]] and provide certification that their product meets the requirements of Sec 1058 will be placed on the qualified list and my be accepted based on brand name.		This qualified list does not represent all products that may be used for those applications listed in Sec 1058. Other products may be accepted based on certification provided to the inspector at the jobsite or on sampling and testing. However, those companies that submit to Construction and Materials for [[106.17 New Product Evaluation\|New Product Evaluation]] and provide certification that their product meets the requirements of Sec 1058 will be placed on the qualified list and my be accepted based on brand name.

	===1058.2 Report (Records)===		===1058.2 Report (Records)===

Smithk: /* 1058.2 Report (Records) */minor clarifications to differentiate EPG articles (that are referenced as "articles", not "sections") from specifications (that are referenced as "sections")

2010-03-31T13:28:40Z

1058.2 Report (Records): minor clarifications to differentiate EPG articles (that are referenced as "articles", not "sections") from specifications (that are referenced as "sections")

← Older revision		Revision as of 08:28, 31 March 2010
Line 34:		Line 34:
	SiteManager and the manufacturer's certification, when used for acceptance, is to be retained in the district office. The report is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify the conditions of acceptance or rejection.		SiteManager and the manufacturer's certification, when used for acceptance, is to be retained in the district office. The report is to indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify the conditions of acceptance or rejection.

	Distribution of reports for materials purchased under a Department purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|1101 Materials Purchased by a Department Purchase Order]].		Distribution of reports for materials purchased under a Department purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|EPG 1101 Materials Purchased by a Department Purchase Order]].

Smithk: article construction

2008-03-04T16:46:05Z

article construction

← Older revision		Revision as of 11:46, 4 March 2008
Line 6:		Line 6:
	\|}		\|}

	This article establishes procedures for inspecting, sampling and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.		This article establishes procedures for inspecting, [[106.5 Sampling\|sampling]] and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.

	===1058.1 Procedure===		===1058.1 Procedure===

Smithk: /* Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM) */article construction

2008-02-07T15:14:41Z

<center>Table 1058 Qualified Brand Names and Manufacturers of Polyethylene Sheeting (1058PSBB, 1058PSCM)</center>: article construction

← Older revision		Revision as of 10:14, 7 February 2008
Line 27:		Line 27:
	\|}		\|}

	This qualified list does not represent all products that may be used for those applications listed in Sec 1058. Other products may be accepted based on certification provided to the inspector at the jobsite or on sampling and testing. However, those companies that submit to Construction and Materials for [[New Product Evaluation]] and provide certification that their product meets the requirements of Sec 1058 will be placed on the qualified list and my be accepted based on brand name.		This qualified list does not represent all products that may be used for those applications listed in Sec 1058. Other products may be accepted based on certification provided to the inspector at the jobsite or on sampling and testing. However, those companies that submit to Construction and Materials for [[106.19 New Product Evaluation\|New Product Evaluation]] and provide certification that their product meets the requirements of Sec 1058 will be placed on the qualified list and my be accepted based on brand name.

	===1058.2 Report (Records)===		===1058.2 Report (Records)===

Smithk: article construction

2007-10-29T17:44:15Z

article construction

← Older revision		Revision as of 12:44, 29 October 2007
Line 1:		Line 1:
			{\|style="padding: 0.3em; margin-left:1px; border:2px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="280px" align="right"
			\|-
			\|'''MGS Information'''
			\|-
			\|[http://www.modot.mo.gov/business/materials/pdf/mgs/MGSINDEX.pdf Current General Services Specifications (MGS) By Subject]
			\|}

	This article establishes procedures for inspecting, sampling and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.		This article establishes procedures for inspecting, sampling and reporting polyethylene sheeting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1058.pdf Sec 1058] for MoDOT’s specifications.