Category:1031 Clay Drain Tile - Revision history

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-10-01T18:11:36Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 13:11, 1 October 2021
Line 42:		Line 42:
	Tests consist of crushing strength, absorption, and freezing and thawing.		Tests consist of crushing strength, absorption, and freezing and thawing.

	'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.		'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through AASHTOWARE Project (AWP).

	'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through AWP.		'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through AWP.

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-09-16T13:54:20Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 08:54, 16 September 2021
Line 25:		Line 25:
	Three-edge bearing tests shall be observed on each size and class of pipe furnished for MoDOT projects. Samples shall be selected and prepared for testing in accordance with AASHTO M 179. The tests are to be performed in accordance with AASHTO T281 and at a frequency of approximately every two years or as deemed necessary.		Three-edge bearing tests shall be observed on each size and class of pipe furnished for MoDOT projects. Samples shall be selected and prepared for testing in accordance with AASHTO M 179. The tests are to be performed in accordance with AASHTO T281 and at a frequency of approximately every two years or as deemed necessary.

	Absorption samples are to be taken from tile broken in three-edge bearing and submitted to the Central Laboratory for testing. Size of sample shall be as specified in AASHTO		Absorption samples are to be taken from tile broken in three-edge bearing and submitted to the Central Laboratory for testing. Size of sample shall be as specified in AASHTO T 281. AASHTOWARE Project (AWP) is to be used when submitting samples to the Central Laboratory and the test for which the sample is being submitted shall be indicated.
	T 281. ~~SiteManager~~ is to be used when submitting samples to the Central Laboratory and the test for which the sample is being submitted shall be indicated.

	===1031.3 Report (Reords)===		===1031.3 Report (Reords)===

	All tile inspected shall be reported in ~~[http://wwwi/intranet/cm/siteManager.htm SiteManager (SM)]~~ acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.		All tile inspected shall be reported in AWP acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.

	Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.		Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.
Line 45:		Line 44:
	'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.		'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.

	'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.		'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through AWP.

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in ~~SM, as described~~ in [[:Category:101 Standard Forms#Sample Record General ~~Information~~\| Sample Record General ~~Information]] [[image:bulldozer.jpg\|20px~~]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [[:Category:101 Standard Forms #Sample Record, General\|AWP MA Sample Record, General]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: updated link

2018-10-11T20:05:36Z

updated link

← Older revision		Revision as of 15:05, 11 October 2018
Line 3:		Line 3:
	\|'''MGS Information'''		\|'''MGS Information'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov/business/materials/pdf~~/mgs~~/MGSINDEX.pdf~~ Current General Services Specifications (MGS) By Subject]		\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]
	\|}		\|}

Smithk: updated link

2016-06-15T17:21:07Z

updated link

← Older revision		Revision as of 12:21, 15 June 2016
Line 6:		Line 6:
	\|}		\|}

	This article establishes procedures for inspecting, accepting and reporting of clay drain tile. Refer to [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1031~~.pdf Sec 1031] for more information.		This article establishes procedures for inspecting, accepting and reporting of clay drain tile. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1031] for more information.

	For Laboratory testing and sample reporting procedures, refer to EPG 1031.4 Laboratory Testing Guidelines for Sec 1031.		For Laboratory testing and sample reporting procedures, refer to EPG 1031.4 Laboratory Testing Guidelines for Sec 1031.

Smithk: updated link

2013-08-22T14:15:39Z

updated link

← Older revision		Revision as of 09:15, 22 August 2013
Line 48:		Line 48:

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in SM, as described in [~~http~~:~~//contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510~~.~~pdf Automation Section 3510~~], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: /* 1031.4.2 Sample Record */ Per CM, updated link to AS 3510

2011-07-05T20:43:51Z

1031.4.2 Sample Record: Per CM, updated link to AS 3510

← Older revision		Revision as of 15:43, 5 July 2011
Line 48:		Line 48:

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in SM, as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: added link

2010-08-30T20:07:57Z

added link

Smithk: /* 1031.4.2 Sample Record */ updated link

2010-07-01T17:49:48Z

1031.4.2 Sample Record: updated link

← Older revision		Revision as of 12:49, 1 July 2010
Line 49:		Line 49:

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.9 Reporting ~~Test Results~~\|EPG 106.9 Reporting ~~Test Results~~]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: minor clarifications

2010-03-31T12:38:42Z

minor clarifications

← Older revision		Revision as of 07:38, 31 March 2010
Line 8:		Line 8:
	This article establishes procedures for inspecting, accepting and reporting of clay drain tile. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1031.pdf Sec 1031] for more information.		This article establishes procedures for inspecting, accepting and reporting of clay drain tile. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1031.pdf Sec 1031] for more information.

	For Laboratory testing and sample reporting procedures, refer to 1031.4 Laboratory Testing Guidelines for Sec 1031.		For Laboratory testing and sample reporting procedures, refer to EPG 1031.4 Laboratory Testing Guidelines for Sec 1031.

	===1031.1 Apparatus===		===1031.1 Apparatus===
Line 34:		Line 34:
	Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.		Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.

	Distribution of reports for materials purchased under a MoDOT purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|1101 Materials Purchased by a Department Purchase Order]]. A report created for a MoDOT purchase order shall at least include the purchase order number on the “Other” tab and the number pieces, total length of tile inspected and an acceptance or rejection statement in the Free Form test.		Distribution of reports for materials purchased under a MoDOT purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|EPG 1101 Materials Purchased by a Department Purchase Order]]. A report created for a MoDOT purchase order shall at least include the purchase order number on the “Other” tab and the number pieces, total length of tile inspected and an acceptance or rejection statement in the Free Form test.

	===1031.4 Laboratory Testing Guidelines for Sec 1031===		===1031.4 Laboratory Testing Guidelines for Sec 1031===
Line 49:		Line 49:

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|EPG 106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: /* 1031.3 Report (Reords) */updated Operations Engineer title to Construction and Materials Engineer

2009-12-28T18:36:52Z

1031.3 Report (Reords): updated Operations Engineer title to Construction and Materials Engineer

← Older revision		Revision as of 13:36, 28 December 2009
Line 32:		Line 32:
	All tile inspected shall be reported in SiteManager acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.		All tile inspected shall be reported in SiteManager acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.

	Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The ~~Operations~~ Engineer will review the test results prior to filing in the district office.		Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.

	Distribution of reports for materials purchased under a MoDOT purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|1101 Materials Purchased by a Department Purchase Order]]. A report created for a MoDOT purchase order shall at least include the purchase order number on the “Other” tab and the number pieces, total length of tile inspected and an acceptance or rejection statement in the Free Form test.		Distribution of reports for materials purchased under a MoDOT purchase order is to be as described in [[:Category:1101 Materials Purchased by a Department Purchase Order\|1101 Materials Purchased by a Department Purchase Order]]. A report created for a MoDOT purchase order shall at least include the purchase order number on the “Other” tab and the number pieces, total length of tile inspected and an acceptance or rejection statement in the Free Form test.

← Older revision		Revision as of 15:07, 30 August 2010
Line 30:		Line 30:
	===1031.3 Report (Reords)===		===1031.3 Report (Reords)===

	All tile inspected shall be reported in SiteManager acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.		All tile inspected shall be reported in [http://wwwi/intranet/cm/siteManager.htm SiteManager (SM)] acceptance or rejection. Acceptance reports shall contain a statement in the Free Form test of the report such as “Three-edge bearing and absorption test results on file in the District Materials Office,” or “Accepted on the basis of manufacturer’s certification on file in the District Office.” Rejection reports shall contain a brief explanation of causes of rejection.

	Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.		Three-edge bearing tests are to be reported on a form similar to [[:category:1030 Vitrified Clay Sewer and Culvert Pipe#Table 1030, Report of Tests on Clay Pipe\|Table 1030, Report of Tests on Clay Pipe]]. The district shall provide its own forms. The Construction and Materials Engineer will review the test results prior to filing in the district office.
Line 38:		Line 38:
	===1031.4 Laboratory Testing Guidelines for Sec 1031===		===1031.4 Laboratory Testing Guidelines for Sec 1031===

	This article establishes procedures for Laboratory testing and reporting samples of clay		This article establishes procedures for Laboratory testing and reporting samples of clay drain tile.
	drain tile.

	====1031.4.1 Procedure====		====1031.4.1 Procedure====
	Tests consist of crushing strength, absorption, and freezing and thawing.		Tests consist of crushing strength, absorption, and freezing and thawing.

	'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through ~~SiteManager~~.		'''Crushing Strength and Absorption Tests.''' Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.

	'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through ~~SiteManager~~.		'''Freezing-and-Thawing Test.''' This test is run only when absorption tests fail to meet requirements and the manufacturer or contractor requests a waiver of absorption requirements. Samples shall be tested in accordance with AASHTO T281. Test results and calculations shall be recorded through SM.

	====1031.4.2 Sample Record====		====1031.4.2 Sample Record====
	The sample record shall be completed in ~~SiteManager~~, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.