614.3 Laboratory Testing Guidelines for Sec 614 - Revision history

Smithk: Per CM, replaced archaic "Automation Section" with AWP MA Sample Record, General

2021-11-24T13:56:08Z

Per CM, replaced archaic "Automation Section" with AWP MA Sample Record, General

← Older revision		Revision as of 08:56, 24 November 2021
Line 5:		Line 5:

	===614.2.2 Sample Record===		===614.2.2 Sample Record===
	The sample record shall be completed in AWP as described in [~~http~~://~~contribute~~.modot.~~mo.gov/business/materials~~/~~pdf~~/~~vol_3~~/~~MMV3CONT~~.~~pdf Automation Section~~] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AWP as described in [https://epg.modot.org/forms/CM/AWP_MA_Sample_Record_General.docx AWP MA Sample Record, General] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:614 Drainage Fittings (Grate Inlets)]]		[[Category:614 Drainage Fittings (Grate Inlets)]]

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-10-01T15:53:19Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 10:53, 1 October 2021
Line 2:		Line 2:

	===614.2.1 Procedure===		===614.2.1 Procedure===
	Grates and bearing plates shall be tested for weight (mass) of zinc coating according to AASHTO M111. Bolts, nuts and washers shall be tested for weight (mass) of zinc coating according to AASHTO M232. Refer to [[:Category:1040 Guardrail, End Terminals, One-Strand Access Restraint Cable and Three-Strand Guard Cable Material#Field determination of weight of coating.\|Field determination of weight of coating]] for additional information concerning the testing of bolts, nuts, and washers for weight (mass) of zinc coating. All test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through ~~SiteManager~~.		Grates and bearing plates shall be tested for weight (mass) of zinc coating according to AASHTO M111. Bolts, nuts and washers shall be tested for weight (mass) of zinc coating according to AASHTO M232. Refer to [[:Category:1040 Guardrail, End Terminals, One-Strand Access Restraint Cable and Three-Strand Guard Cable Material#Field determination of weight of coating.\|Field determination of weight of coating]] for additional information concerning the testing of bolts, nuts, and washers for weight (mass) of zinc coating. All test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWARE Project (AWP).

	===614.2.2 Sample Record===		===614.2.2 Sample Record===
	The sample record shall be completed in ~~SiteManager~~ as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/MMV3CONT.pdf Automation Section] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AWP as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/MMV3CONT.pdf Automation Section] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:614 Drainage Fittings (Grate Inlets)]]		[[Category:614 Drainage Fittings (Grate Inlets)]]

Smithk: updated link

2016-06-09T15:04:26Z

updated link

← Older revision		Revision as of 10:04, 9 June 2016
Line 1:		Line 1:
	This article establishes procedures for Laboratory testing and reporting samples of grates, bearing plates, bolts, nuts and washers. No Laboratory tests are required for automatic floodgates, manhole frames and covers or curb inlets. Refer to [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec0614~~.pdf Sec 614] for MoDOT's specifications.		This article establishes procedures for Laboratory testing and reporting samples of grates, bearing plates, bolts, nuts and washers. No Laboratory tests are required for automatic floodgates, manhole frames and covers or curb inlets. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=9 Sec 614] for MoDOT's specifications.

	===614.2.1 Procedure===		===614.2.1 Procedure===

Smithk: /* 614.2.2 Sample Record */ Per CM, updated link

2013-10-10T16:17:10Z

614.2.2 Sample Record: Per CM, updated link

← Older revision		Revision as of 11:17, 10 October 2013
Line 5:		Line 5:

	===614.2.2 Sample Record===		===614.2.2 Sample Record===
	The sample record shall be completed in SiteManager as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/~~AS3510~~.pdf Automation Section ~~3510~~] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/MMV3CONT.pdf Automation Section] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:614 Drainage Fittings (Grate Inlets)]]		[[Category:614 Drainage Fittings (Grate Inlets)]]

Smithk: /* 614.2.2 Sample Record */ Per CM, link updated to AS 3510

2011-07-05T20:13:20Z

614.2.2 Sample Record: Per CM, link updated to AS 3510

← Older revision		Revision as of 15:13, 5 July 2011
Line 5:		Line 5:

	===614.2.2 Sample Record===		===614.2.2 Sample Record===
	The sample record shall be completed in SiteManager as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:614 Drainage Fittings (Grate Inlets)]]		[[Category:614 Drainage Fittings (Grate Inlets)]]

Smithk: /* 614.2.2 Sample Record */ updated link

2010-07-01T18:52:21Z

614.2.2 Sample Record: updated link

← Older revision		Revision as of 13:52, 1 July 2010
Line 5:		Line 5:

	===614.2.2 Sample Record===		===614.2.2 Sample Record===
	The sample record shall be completed in SiteManager as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.9 Reporting ~~Test Results~~\|106.9 Reporting ~~Test Results~~]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:614 Drainage Fittings (Grate Inlets)]]		[[Category:614 Drainage Fittings (Grate Inlets)]]

Smithk: /* 614.2.1 Procedure */article construction

2009-04-02T17:50:18Z

614.2.1 Procedure: article construction

← Older revision		Revision as of 12:50, 2 April 2009
Line 2:		Line 2:

	===614.2.1 Procedure===		===614.2.1 Procedure===
	Grates and bearing plates shall be tested for weight (mass) of zinc coating according to AASHTO M111. Bolts, nuts and washers shall be tested for weight (mass) of zinc coating according to AASHTO M232. Refer to [[:Category:1040 Guardrail, End Terminals, One-Strand Access Restraint Cable and Three-Strand Guard Cable Material#Field determination of weight of coating\|Field determination of weight of coating]] for additional information concerning the testing of bolts, nuts, and washers for weight (mass) of zinc coating. All test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.		Grates and bearing plates shall be tested for weight (mass) of zinc coating according to AASHTO M111. Bolts, nuts and washers shall be tested for weight (mass) of zinc coating according to AASHTO M232. Refer to [[:Category:1040 Guardrail, End Terminals, One-Strand Access Restraint Cable and Three-Strand Guard Cable Material#Field determination of weight of coating.\|Field determination of weight of coating]] for additional information concerning the testing of bolts, nuts, and washers for weight (mass) of zinc coating. All test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.

	===614.2.2 Sample Record===		===614.2.2 Sample Record===

Smithk: article construction

2008-02-21T15:24:32Z

article construction

New page

This article establishes procedures for Laboratory testing and reporting samples of grates, bearing plates, bolts, nuts and washers. No Laboratory tests are required for automatic floodgates, manhole frames and covers or curb inlets. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec0614.pdf Sec 614] for MoDOT's specifications.

===614.2.1 Procedure===
Grates and bearing plates shall be tested for weight (mass) of zinc coating according to AASHTO M111. Bolts, nuts and washers shall be tested for weight (mass) of zinc coating according to AASHTO M232. Refer to [[:Category:1040 Guardrail, End Terminals, One-Strand Access Restraint Cable and Three-Strand Guard Cable Material#Field determination of weight of coating|Field determination of weight of coating]] for additional information concerning the testing of bolts, nuts, and washers for weight (mass) of zinc coating. All test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.

===614.2.2 Sample Record===
The sample record shall be completed in SiteManager as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510] and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results|106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

[[Category:614 Drainage Fittings (Grate Inlets)]]